Disclaimer: This is an example of a student written essay.
Click here for sample essays written by our professional writers.

Any scientific information contained within this essay should not be treated as fact, this content is to be used for educational purposes only and may contain factual inaccuracies or be out of date.

Operation Of TWT And Magnetrons

Paper Type: Free Essay Subject: Engineering
Wordcount: 3161 words Published: 17th May 2017

Reference this

A traveling-wave tube (TWT) is an electronic device used to amplify radio frequency signals to high power, usually in an electronic assembly known as a traveling-wave tube amplifier (TWTA).

The bandwidth of a broadband TWT can be as high as three octaves, although tuned (narrowband) versions exist, and operating frequencies range from 300 MHz to 50 GHz. The voltage gain of the tube can be of the order of 70 decibels.

Traveling-Wave Tubes Traveling-wave tubes (TWTs) are high-gain, low- noise, wide and width microwave amplifiers, capable of gains of 40 dB or more, with bandwidths of over an octave. (A bandwidth of 1 octave is one in which the upper frequency is twice the lower frequency.) TWTs have been designed for frequencies as low as 300 MHz and as high as 50 GHz. The primary use for

Get Help With Your Essay

If you need assistance with writing your essay, our professional essay writing service is here to help!

Essay Writing Service

TWTs is voltage amplification (although high-power TWTs, with characteristics similar to those of a power klystron, have been developed). Their wide bandwidth and low-noise characteristics make them ideal for use as RF amplifiers.

CONSTRUCTION:

The device is an elongated vacuum tube with an electron gun (a heated cathode that emits electrons) at one end. A magnetic containment field around the tube focuses the electrons into a beam, which then passes down the middle of a wire helix that stretches from the RF input to the RF output, the electron beam finally striking a collector at the other end. A directional coupler, which can be either a waveguide or an electromagnetic coil, fed with the low-powered radio signal that is to be amplified, is positioned near the emitter, and induces a current into the helix.

The helix acts as a delay line, in which the RF signal travels at near the same speed along the tube as the electron beam. The electromagnetic field due to the RF signal in the helix interacts with the electron beam, causing bunching of the electrons (an effect called velocity modulation), and the electromagnetic field due to the beam current then induces more current back into the helix (i.e. the current builds up and thus is amplified as it passes down).

A second directional coupler, positioned near the collector, receives an amplified version of the input signal from the far end of the helix. An attenuator placed on the helix, usually between the input and output helicies, prevents reflected wave from travelling back to the cathode.

Higher powered TWT’s usually contain beryllium oxide ceramic as both a helix support rod and in some cases, as an electron collector for the TWT because of its special electrical, mechanical, and thermal properties.

OPERATION AND WORKING

While the electron beam in a klystron travels primarily in regions free of RF electric fields, the beam in a TWT is continually inter- acting with an RF electric field propagating along an external circuit surrounding the beam. To obtain amplification, the TWT must propagate a wave whose phase velocity is nearly synchronous with the dc velocity of the electron beam. It is difficult to accelerate the beam to greater than approximately one- fifth the velocity of light. Therefore, the forward velocity of the RF field propagating along the helix must be reduced to nearly that of the beam. The phase velocity in a waveguide, which is uniform in the direction of propagation, is always greater than the velocity of light. However, this velocity can be reduced below the velocity of light by introducing a periodic variation of the circuit in the direction of propagation. The simplest form of variation is obtained by wrapping the circuit in the form of a helix, whose pitch is equal to the desired slowing factor.

TWT MIXER.- A TWT is also used as a micro- wave mixer. By virtue of its wide bandwidth, the TWT can accommodate the frequencies generated by the heterodyning process (provided that the frequencies have been chosen to be within the range of the tube). The desired frequency is selected by the use of a filter on the output of the helix. A TWT mixer has the added advantage of providing gain as well as simply acting as a mixer.

TWT MODULATION.- A TWT can be modulated by applying the modulating signal to a modulator grid. The modulator grid can be used to turn the electron beam on and off, as in pulsed microwave applications, or to control the density of the beam and its ability to transfer energy to the traveling wave. Thus, the grid can be used to amplitude modulate the output.

TWT OSCILLATOR.- A forward-wave TWT can be constructed to serve as a microwave oscillator. Physically, a TWT amplifier and an oscillator differ in two major ways. The helix of the oscillator is longer than that of the amplifier, and there is no input connection to the oscillator. TWT oscillators are often called backward-wave oscillators (BWOs) or carcintrons.

The Traveling-Wave Tube The TRAVELING-WAVE TUBE (twt) is a high-gain, low-noise, wide-bandwidth microwave amplifier. It is capable of gains greater than 40 dB with bandwidths exceeding an octave. (A bandwidth of 1 octave is one in which the upper frequency is twice the lower frequency.) Traveling-wave tubes have been designed for frequencies as low as 300 megahertz and as high as 50 gigahertz. The twt is primarily a voltage amplifier. The wide-bandwidth and low-noise characteristics make the twt ideal for use as an RF amplifier in microwave equipment. The physical construction of a typical twt is shown in figure 2-13.

Fig-2

The twt contains an electron gun which produces and then accelerates an electron beam along the axis of the tube. The surrounding magnet provides a magnetic field along the axis of the tube to focus the electrons into a tight beam. The HELIX, at the center of the tube, is a coiled wire that provides a low-impedance transmission line for the RF energy within the tube. The RF input and output are coupled onto and removed from the helix by directional couplers that have no physical connection to the helix. If the RF energy is transported on coaxial cables, the coaxial couplers are wound in a helical manner similar to that shown in figure 2. If the RF energy is transported in waveguides, waveguide directional couplers are used. The attenuator prevents any reflected waves from traveling back down the helix. Physical construction of a twt. A simplified version of twt operation is shown in fig below. In the figure, an electron beam is passing along a nonresonant transmission line represented by a straight wire. The input to the transmission line is an RF wave which travels on the line from input to output. The line will transport a wide range of RF frequencies if it is terminated in the characteristic impedance of the line. The electromagnetic waves traveling down the line produce electric fields that interact with the electrons of the beam.

Fig:-3

If the electrons of the beam were accelerated to travel faster than the waves traveling on the wire, bunching would occur through the effect of velocity modulation. Velocity modulation would be caused by the interaction between the traveling-wave fields and the electron beam. Bunching would cause the electrons to give up energy to the traveling wave if the fields were of the correct polarity to slow down the bunches. The energy from the bunches would increase the amplitude of the traveling wave in a progressive action that would take place all along the length of the twt, as shown in figure . However, because the waves travel along the wire at the speed of light, the simple twt shown in figure 3 will not work. At present no way is known to accelerate an electron beam to the speed of light. Since the electron beam cannot travel faster than the wave on the wire, bunching will not take place and the tube will not work. The twt is therefore designed with a delay structure to slow the traveling wave down to or below the speed of the electrons in the beam. A common twt delay structure is a wire, wound in the form of a long coil or helix, as shown in figure , view (A). The shape of the helix slows the effective velocity of the wave along the common axis of the helix and the tube to about one-tenth the speed of light. The wave still travels down the helix wire at the speed of light, but the coiled shape causes the wave to travel a much greater total distance than the electron beam. The speed at which the wave travels down the tube can be varied by changing the number of turns or the diameter of the turns in the helix wire. The helical delay structure works well because it has the added advantage of causing a large proportion of electric fields that are parallel to the electron beam. The parallel fields provide maximum interaction between the fields and the electron beam.

In a typical twt, the electron beam is directed down the center of the helix while, at the same time, an RF signal is coupled onto the helix. The electrons of the beam are velocity-modulated by the electric fields produced by the RF signal. Amplification begins as the electron bunches form and release energy to the signal on the helix. The slightly amplified signal causes a denser electron bunch which, in turn, amplifies the signal even more. The amplification process is continuous as the RF wave and the electron beam travel down the length of the tube. Any portion of the twt output signal that reflects back to the input will cause oscillations within the tube which results in a decrease in amplification. Attenuators are placed along the length of the helix to prevent reflections from reaching the input. The attenuator causes a loss in amplitude, as can be seen in figure , view (B), but it can be placed so as to minimize losses while still isolating the input from the output. The relatively low efficiency of the twt partially offsets the advantages of high gain and wide bandwidth. The internal attenuator reduces the gain of the tube, and the power required to energize the focusing magnet is an operational loss that cannot be recovered. The twt also produces heat which must be dissipated by either air-conditioning or liquid-cooling systems. All of these factors reduce the overall efficiency of the twt, but the advantages of high gain and wide bandwidth are usually enough to overcome the disadvantages.

THE MAGNETRON

The MAGNETRON, shown in figure 4-A, is a self-contained microwave oscillator that operates differently from the linear-beam tubes, such as the twt and the klystron. Figure 4-B is a simplified drawing of the magnetron. CROSSED-ELECTRON and MAGNETIC fields are used in the magnetron to produce the high-power output required in radar and communications equipment.

Figure 4.A.-Magnetron

Figure4 b.-Magnetron

The magnetron is classed as a diode because it has no grid. A magnetic field located in the space between the plate (anode) and the cathode serves as a grid. The plate of a magnetron does not have the same physical appearance as the plate of an ordinary electron tube. Since conventional inductive- capacitive (LC) networks become impractical at microwave frequencies, the plate is fabricated into a cylindrical copper block containing resonant cavities which serve as tuned circuits. The magnetron base differs considerably from the conventional tube base. The magnetron base is short in length and has large diameter leads that are carefully sealed into the tube and shielded. The cathode and filament are at the center of the tube and are supported by the filament leads. The filament leads are large and rigid enough to keep the cathode and filament structure fixed in position. The output lead is usually a probe or loop extending into one of the tuned cavities and coupled into a waveguide or coaxial line. The plate structure, shown in figure 5, is a solid block of copper. The cylindrical holes around its circumference are resonant cavities. A narrow slot runs from each cavity into the central portion of the tube dividing the inner structure into as many segments as there are cavities. Alternate segments are strapped together to put the cavities in parallel with regard to the output. The cavities control the output frequency. The straps are circular, metal bands that are placed across the top of the block at the entrance slots to the cavities. Since the cathode must operate at high power, it must be fairly large and must also be able to withstand high operating temperatures. It must also have good emission characteristics, particularly under return bombardment by the electrons. This is because most of the output power is provided by the large number of electrons that are emitted when high-velocity electrons return to strike the cathode. The cathode is indirectly heated and is constructed of a high- emission material. The open space between the plate and the cathode is called the INTERACTION SPACE. In this space the electric and magnetic fields interact to exert force upon the electrons.

Figure 5.-Cutaway view of a magnetron

The magnetic field is usually provided by a strong, permanent magnet mounted around the magnetron so that the magnetic field is parallel with the axis of the cathode. The cathode is mounted in the center of the interaction space. BASIC MAGNETRON OPERATION.-Magnetron theory of operation is based on the motion of electrons under the influence of combined electric and magnetic fields. The following information presents the laws governing this motion. The direction of an electric field is from the positive electrode to the negative electrode. The law governing the motion of an electron in an electric field (E field) states: The force exerted by an electric field on an electron is proportional to the strength of the field. Electrons tend to move from a point of negative potential toward a positive potential.

This is shown in figure 6. In other words, electrons tend to move against the E field. When an electron is being accelerated by an E field, as shown in figure 6, energy is taken from the field by the electron.

Figure 6.-Electron motion in an electric field

The law of motion of an electron in a magnetic field (H field) states: The force exerted on an electron in a magnetic field is at right angles to both the field and the path of the electron. The direction of the force is such that the electron trajectories are clockwise when viewed in the direction of the magnetic field. This is shown in figure 7.

Figure 7.-Electron motion in a magnetic field

In figure 7, assume that a south pole is below the figure and a north pole is above the figure so that the magnetic field is going into the paper. When an electron is moving through space, a magnetic field builds around the electron just as it would around a wire when electrons are flowing through a wire. In figure 7 the magnetic field around the moving electron adds to the permanent magnetic field on the left side of the electron’s path and subtracts from the permanent magnetic field on the right side. This action weakens the field on the right side; therefore, the electron path bends to the right (clockwise). If the strength of the magnetic field is increased, the path of the electron will have a sharper bend. Likewise, if the velocity of the electron increases, the field around it increases and the path will bend more sharply. A schematic diagram of a basic magnetron is shown in figure 8A. The tube consists of a cylindrical plate with a cathode placed along the center axis of the plate. The tuned circuit is made up of cavities in which oscillations take place and are physically located in the plate. When no magnetic field exists, heating the cathode results in a uniform and direct movement of the field from the cathode to the plate, as illustrated in figure 8B. However, as the magnetic field surrounding the tube is increased, a single electron is affected, as shown in figure 9. In figure 9, view (A), the magnetic field has been increased to a point where the electron proceeds to the plate in a curve rather than a direct path.

Figure 8A.-Basic magnetron. SIDE VIEW

Figure 9.-Effect of a magnetic field on a single electron

In view (B) of figure 9, the magnetic field has reached a value great enough to cause the electron to just miss the plate and return to the filament in a circular orbit. This value is the CRITICAL VALUE of field strength. In view (C), the value of the field strength has been increased to a point beyond the critical value; the electron is made to travel to the cathode in a circular path of smaller diameter. View (D) of figure 9. shows how the magnetron plate current varies under the influence of the varying magnetic field. In view (A), the electron flow reaches the plate, so a large amount of plate current is flowing. However, when the critical field value is reached, as shown in view (B), the electrons are deflected away from the plate and the plate current then drops quickly to a very small value. When the field strength is made still greater, as shown in view (C), the plate current drops to zero. When the magnetron is adjusted to the cutoff, or critical value of the plate current, and the electrons just fail to reach the plate in their circular motion, it can produce oscillations at microwave frequencies. These oscillations are caused by the currents induced electrostatically by the moving electrons. The frequency is determined by the time it takes the electrons to travel from the cathode toward the plate and back again. A transfer of microwave energy to a load is made possible by connecting an external circuit between the cathode and the plate of the magnetron. Magnetron oscillators are divided into two classes: NEGATIVE-RESISTANCE and ELECTRON-RESONANCE MAGNETRON OSCILLATORS. A negative-resistance magnetron oscillator is operated by a static negative resistance between its electrodes. This oscillator has a frequency equal to the frequency of the tuned circuit connected to the tube. An electron-resonance magnetron oscillator is operated by the electron transit time required for electrons to travel from cathode to plate. This oscillator is capable of generating very large peak power outputs at frequencies in the thousands of megahertz. Although its average power output over a period of time is low, it can provide very high-powered oscillations in short bursts of pulses.

 

Cite This Work

To export a reference to this article please select a referencing stye below:

Reference Copied to Clipboard.
Reference Copied to Clipboard.
Reference Copied to Clipboard.
Reference Copied to Clipboard.
Reference Copied to Clipboard.
Reference Copied to Clipboard.
Reference Copied to Clipboard.

Related Services

View all

DMCA / Removal Request

If you are the original writer of this essay and no longer wish to have your work published on UKEssays.com then please: